Behringer FEEDBACK DESTROYER PRO DSP1124P Manual de usuario

Users ManualVersion 1.0 February 2001www.behringer.comFEEDBACK DESTROYER® PRO DSP1124PENGLISHDATA-MANFULL_DSP1124P_ENG_Rev. A.p65 02.03.01, 1

10FEEDBACK DESTROYER PRO DSP1124P2.4 Using the FEEDBACK DESTROYER PRO in a studio environmentWith its highly flexible configuration the DSP1124P also

11FEEDBACK DESTROYER PRO DSP1124Ps A filter has been set, i.e. it is already suppressing feedback; or:s A filter is set to Parametric EQ mode (gain

12FEEDBACK DESTROYER PRO DSP1124P13The GAIN key sets the desired boost/cut of the selected filter in dB (+16 dB/-48 dB).14The IN/OUT key allows for op

13FEEDBACK DESTROYER PRO DSP1124P5. DSP1124P ARCHITECTURE: PRESETS, FILTERS, OPERATINGMODESIn order to avoid confusion, let us give you a concise

14FEEDBACK DESTROYER PRO DSP1124P6. OPERATING MODES OF THE DSP1124PThe individual filters on the BEHRINGER FEEDBACK DESTROYER PRO can operate in f

15FEEDBACK DESTROYER PRO DSP1124P6.4 Locked mode (LO)When the DSP1124P detects a feedback frequency in Single-Shot mode (see chapter 6.3), it automa

16FEEDBACK DESTROYER PRO DSP1124P+ To avoid inadvertent changing of filter modes, the filter mode selection takes place afterabout one se

17FEEDBACK DESTROYER PRO DSP1124P8. PROBLEMS DO HAVE A CAUSE ...Feedback is one of the major problems encountered in live P.A. applications. In a wors

18FEEDBACK DESTROYER PRO DSP1124PThe fifth page of the MIDI menu shows the Store Enable flag represented by a capital S in the DISPLAY.Available v

19FEEDBACK DESTROYER PRO DSP1124PFig. 10.1: Different plug typesFig. 10.2: Wiring an insert cable+ Please ensure that only qualified persons install a

2FEEDBACK DESTROYER PRO DSP1124PThis symbol, wherever it appears, alertsyou to the presence of uninsulateddangerous voltage inside the enclosure-

20FEEDBACK DESTROYER PRO DSP1124P10.2 MIDI connectionsThe MIDI connectors found on the rear panel are on internationally standardized 5-pin DIN jacks.

21FEEDBACK DESTROYER PRO DSP1124Pincrement()∆ fffnnn=−+120Hz20 25 31.5 40 50 63 80 100 125 160 200 250 315 400 500 630 800kHz1 1.25 1.6 2 2.5 3.15 4 5

22FEEDBACK DESTROYER PRO DSP1124P11.3 MIDI implementationFunction Transmitted Recognized RemarksBasic ChannelDefaultChangedOFF, 1 - 16OFF, 1 - 16OFF,

23FEEDBACK DESTROYER PRO DSP1124P12. SPECIFICATIONSAUDIO INPUTSConnectors XLR and 1/4" TRSType RF filtered, servo-balanced inputImpedance 60 kOhm

24FEEDBACK DESTROYER PRO DSP1124P13. WARRANTYThe information contained in this manual is subject to change without notice. No part of this manual may

FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATIONResponsible party name: MUSIC Group Services USA, Inc.Address: 18912 North Creek Parkway, Su

3FEEDBACK DESTROYER PRO DSP1124PFOREWORDDear Customer,Welcome to the team of FEEDBACK DESTROYER PRO users and thank you very much for expressing yourc

4FEEDBACK DESTROYER PRO DSP1124PDSP1124PFEEDBACK DESTROYER® PRO24-Bit Dual Engine Digital Feedback Destroyer / Parametric EQ Model DSP1124PsUltra-hi

5FEEDBACK DESTROYER PRO DSP1124PTABLE OF CONTENTS1. INTRODUCTION...

6FEEDBACK DESTROYER PRO DSP1124P1. INTRODUCTIONThank you very much for expressing your confidence in BEHRINGER products by purchasing the

7FEEDBACK DESTROYER PRO DSP1124P+ Please note that all units must be grounded properly. For your own safety, you should neverremove any ground conn

8FEEDBACK DESTROYER PRO DSP1124P2. APPLICATIONSThe DSP1124P is used exclusively to eliminate feedback in FOH and monitor mixes.Before you go on, pleas

9FEEDBACK DESTROYER PRO DSP1124PFig. 2.1: Using the DSP1124P in the monitor sends2.3 Using the FEEDBACK DESTROYER PRO in the FOH mixSince you want to