Behringer Digital Pro Mixer DDM4000 Manual de usuario descargar pdf (Pagina 12)

12 DIGITAL PRO MIXER DDM4000 User Manual

3.2.2 Channel setup

In Channel Setup, you can ne-tune the characteristics of the stereo

channels’ equalizer. It is also possible to adjust a Subsonic Filter (low-cut

lter) for all four channels. For example, this lter can be used to suppress

low-frequency noise from turntables.

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Channel Setup” by turning and pressing the CONSOLE SETUP knob.

Channel Setup appears on the display.

The equalizer of the stereo channels has 3 bands with dierent characteristics.

The Mid band is a peak lter whose center fre-quency and bandwidth

(Q factor) can be modied. Both outer bands Low and High are shelving lters.

In Channel Setup, following settings are available for each of the 4 channels:

Channel Xover (Crossover):

LOW: Cuto frequency of the Low lter. All frequencies below the adjusted

value are cut or boosted.

MID: Center frequency of the Mid band. All frequencies around this value

are boosted or cut. The bandwidth is determined by the parameter Mid Q

(see below).

HIGH: Cuto frequency of the High lter. All frequencies above the adjusted

value are boosted or cut.

1) Press the left PARAMETER knob (45) to select the parameter

(LOW, MID or HIGH).

2) Turn the PARAMETER knob to change the cuto frequency and center

frequency of the selected band.

Mid Q:

The Q factor determines the behavior of the lter. The higher the value,

the narrower the bandwidth. Mid Q aects the mids band.

• Turn the CONSOLE SETUP knob (51) to change the value of the Q factor.

Subsonic frequency:

You can adjust the cuto frequency of the low-cut lter on each stereo channel.

All frequencies below the cuto frequency are attenuated.

1) Press the right PARAMETER knob (45) to select the channel.

2) Turn the PARAMETER knob to change the cuto frequency.

Exiting Channel Setup:

• Press the ESC push button (52) to exit Channel Setup.

3.3 Operating the microphone channel

3.3.1 Mic setup

You can make adjustments to the sound settings of the Microphone channel,

the Ultramic processor and the Mic eects by using Mic Setup. This is how to

access Mic Setup:

1) Press the CONSOLE SETUP knob (51) for approximately 2 seconds.

2) Select “Mic Setup” by turning and pressing the CONSOLE SETUP knob.

Alternatively, you can access Mic Setup as follows:

• Press the MIC SETUP push button (16) on the microphone channel.

The MIC SETUP push button lights up as long as you are using Mic Setup.

Mic Setup appears on the display containing several submenus. On the

left-hand side of the display you see a list from which the following submenus

can be selected:

• Turn the left PARAMETER knob (45) to select the submenu you want to edit:

EQ Freq/Pan page:

This page shows level meters for both microphone signals. In addition, you can

make sound settings for the equalizer on the Microphone channel. Here you can

adjust the stereo image of the microphone signal as well as the signal relation

of both microphones to each other. The individual parameters are as follows:

MIC 1: Level meter for Microphone 1

MIC 2: Level meter for Microphone 2

LOW: Cuto frequency of the LOW control knob

MID: Center frequency of the MID control knob

HIGH: Cuto frequency of the HIGH control knob

Q MID: Q factor of the mids band

1) Press the CONSOLE SETUP knob (51) to select the parameter

(LOW, MID, HIGH, Q MID).

2) Turn the CONSOLE SETUP knob to change the value of the selected parameter.

PAN1: Position of Microphone 1 in the stereo image

PAN 2: Position of Microphone 2 in the stereo image

OUT B: Volume of the microphone channel at Output B

1) Press the right PARAMETER knob (45) to select the parameter

(PAN 1, PAN 2, OUT B).

2) Turn the PARAMETER knob to change the value of the parameter.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 31 32

Comentarios a estos manuales

Sin comentarios

Behringer Digital Pro Mixer DDM4000 Manual de usuario Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Controladores de dj Behringer Digital Pro Mixer DDM4000