Behringer Digital Pro Mixer DDM4000 Manual de usuario descargar pdf (Pagina 8)

8 DIGITAL PRO MIXER DDM4000 User Manual

2.5 BPM and eects section

(41) (46)

(47)

(48) (51)

(50)

(45)

(50)

(42) (49) (43) (52)(53)

Fig. 2.5: BPM Counter and Eects section (here FX 1)

The DDM4000 has 2 identical eects units. There are 2 additional independent

eects units for the mic signal and the Sampler. All eects can be used at the

same time. The BPM Counter and MIDI Clock are also found in this section.

(41) The graphic display shows BPM values, eect names and eect parameters

as well as channel assignments. It also leads you through Console Setup.

(42) The FX ON push button activates the eects unit.

(43) Press the FX ASSIGN push button to assign an eects unit to a

signal source (push button ashes). The possible input sources are listed

on the display. Select the preferred source by turning and pressing the

PARAMETER knob (45).

(44) The DEPTH knob adjusts the eect intensity (depth). For some eects,

it also lets you adjust the mix between the original signal (dry) and

the eect signal (wet).

(45) Press the PARAM (eter) knob to select the eect parameters. By turning

the knob, you can change the parameter shown on the display.

(46) Press SELECT/LOW to access the eects list (on the display). Turn and press

the knob (45) to load a preset.

(47) Press the PARAM/MID push button to access the eect parameters.

Turn the knob (45) to change the parameter value.

(48) Press DEFAULT/HIGH to restore a preset.

◊ When the effect is activated (by pressing the FX ON push button),

the push buttons (46) (LOW), (47) (MID) and (48) (HIGH) are used as

Kill switches in the effect’s signal path.

(49) Depending on the selected eect, the BEAT push buttons can adjust

time-related parameters. However, the values entered are not in

milliseconds or similar units, but in beats.

(50) To enter the tempo manually, tap this push button (at least 2 x) in the rhythm

of the music (TAP). By keeping the AUTO BPM/TAP push button pressed a

little longer (> 1 s), the automatic tempo input (AUTO BPM) is reactivated.

(51) Turn the CONSOLE SETUP knob to adjust the tempo of the MIDI Clock

(press and turn simultaneously = coarse adjustment). A short press on

the knob conrms the entry made. A long press on the knob lets you

access Console Setup (see Chapter 3.1).

(52) The MIDI START/STOP/ESC turns on the MIDI Clock.

(53) The ADJUST push buttons let you transfer the tempo of the BPM counter

to the MIDI Clock.

◊ All functions of the BPM and Effects section are described in

detail in Chapter 4.

2.6 Sampler

(54)(54)

(57)

(59)

(63)

(65)

(62)

(56)

(60)

(64)

(66)

(61)

(58)

Fig. 2.6: Sampler section

(54) Press the INSERT push button to add the sampler signal to the channel

(Insert Mode). If the push button is not activated, the sampler is mixed to

the selected channel (Mix Mode). In both cases, playback is initiated with

the REC SOURCE push buttons. When the sampler is routed to the crossfader,

the LED of the INSERT push button goes out.

(55) The VOLUME/MIX knob controls the volume of the sampler (in Mix Mode)

as well as the volume balance between input signal and Sampler

(in Insert Mode).

(56) The REC SOURCE push buttons let you select the channel for recording

and playing back samples.

(57) Press the PFL push button to listen in on the sampler signal with the headphones.

(58) SAMPLE LENGTH adjusts the recording time (1–16 beats or endless recording ∞).

(59) RECORD/IN lets you record to the Sampler. Select a bank beforehand.

By pressing the push button a second time, the recording is stopped

(only in ∞ Mode).

(60) BANK ASSIGN is used to select a bank in which the recorded material

is stored. The selected bank is indicated by the relevant MODE push button

(61) which signalizes the readiness to record.

(61) The MODE push buttons (Bank 1 and Bank 2) are used to select the sampler’s

types of playback (Reverse and Loop). A short tap activates or deactivates

the Reverse function; pressing the push button a little longer activates or

deactivates the Loop function.

(62) Press the PLAY/OUT push button to start the playback of the

recorded sample. When the Loop function is deactivated, the sample is

only played back as long as the PLAY push button is pressed.

(63) Press SMP FX ON push button to activate the Brake eect.

(64) Press the SELECT push button to determine the length of the brake

(1, 4 or 8 Beat Brake, which is shown in the center of the display).

(65) The CF ASSIGN push button lets you determine on which side of the

crossfader the sampler signal is to be routed to.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Comentarios a estos manuales

Sin comentarios

Behringer Digital Pro Mixer DDM4000 Manual de usuario Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para Controladores de dj Behringer Digital Pro Mixer DDM4000